Hi Michal Vodicka ,
Many thanks to you . We solved the problem ,actually the problem is in driver , not in inf .Thanks for your reply .
Thanks & Regards,
Cyril.
From: Michal Vodicka
>Reply-To: “NT Developers Interest List”
>To: “NT Developers Interest List”
>Subject: [ntdev] RE: Help Required : PPPOE NT Driver installation
>Date: Fri, 12 Oct 2001 23:21:27 +0200
>
>Maybe I missed something but have you checked event log? The error message
>can contain important info.
>
>IM driver installation on NT4 isn’t easy and ImSamp INF script is quite
>insufficient. RasMan service is extremely fragile and a small omission in IM
>driver installation can cause unexpected problems. IIRC RasMan reads
>registry at HKLM\SOFTWARE\Microsoft\Windows NT\NetworkCards and creates a
>list of was adapter based on ProductName and/or ServiceName for every card
>(seems crazy? yes! this is one of reasons why it is hard to write IM driver
>over NdisWan). An unexpected value can bring it down. There is no docs,
>AFAIK. To see how to fix a problem I can recommend reading INF scripts for
>RAS and disassembling RasMan service.
>
>There was a free implementation of PPPOE driver for w2k and w9x. I’m not
>sure if it was also for NT4. Maybe you could try to contact author; search
>'Net for RasPPPOE.
>
>Best regards,
>
>Michal Vodicka
>Veridicom
>(RKK - Skytale)
>[WWW: http://www.veridicom.com , http://www.skytale.com]
>
>
>
> > ----------
> > From: sagaya cyril[SMTP:xxxxx@hotmail.com]
> > Reply To: NT Developers Interest List
> > Sent: Friday, October 12, 2001 9:03 PM
> > To: NT Developers Interest List
> > Subject: [ntdev] Help Required : PPPOE NT Driver installation
> >
> > Hi All ,
> > I am having a problem in PPPOE driver installation on Windows NT platform
> > . This is what the pbm i’m facing described below in detail.
> >
> > I am porting PPPOE Driver code of Windows 2000 to windows NT . I have
> > replaced the calls that are not supported in Windows NT by appropriate
> > equalvalent calls . Then I compiled that code using NT DDk . Since it a
> > intermediate driver , it has two edges, Upper WanMiniport edge and Lower
> > Protocol edge .So we bind the lower edge to Lan NIC driver i.e. our
> > protocol binds with lower NIC card. Upper WanMiniport edge binds with
> > NdisTapi .I am using the oemsetup.inf which is combination of IMSMAP
> > inf(older version) and one Wan Miniport inf .I used Wan Miniport .inf only
> > for TAPI stuff .
> >
> > Here the installation sequeneces which we followed .
> > 1. Installed Windows NT workstation
> > 2. Install Service pack 6.0
> > 3. Installed the Ethernet card driver and assinged the IP address .
> > 4. To check the Connection thro the ethernet card is alive i run a ping ,
> > it goes thro fine .
> > 5. Installed PPPOE driver as a Protocol .
> > 6. Installed the RAS , that time we got “WIPPPPOEMP” as the RAS Device .
> > then reboot the system
> > 7. After rebooting when i tried create dialup by clicking the Dialup
> > Networking i got error
> > " 711 RasMan initialization failure. Check the event log. "
> > 8. Then i tried to check the RAS device by going to NCPA
> > ->services->select Remote Access Service -> Click Properties.
> > I got Error Message , that says the device has been removed from the
> > port . Then I got WIPPPOE as RAS device .
> > 9. At this stage without rebooting we are able to dial and create the
> > shotcut for the dialup .
> > The connection is made with the server at this stage .The Data path is
> > clear Ping goes fine with server IP .
> > 10. After the reboot the RAS device disappears with error message
> > " 711 RasMan initialization failure. Check the event log. ".
> > 11. This time i tried to check the RAS device by going to NCPA
> > ->services->select Remote Access Service -> Click Properties.
> > I got Error Message , that says the device has been removed from the
> > port . No ras device as in the case of first reboot.
> >
> >
> > Note : In Driver now we are exposing our device as “ISDN\0WIPPPPOE\0” in
> > GetDevConfig , which is our Protocol.
> >
> > WIPPPOE - Protocol name
> > WIPPPOEMP - Miniport name
> >
> > Thanks and Regards,
> > B.S.Cyril.
> >
> > _____
> >
> > Get your FREE download of MSN Explorer at http://explorer.msn.com
> > —
> > You are currently subscribed to ntdev as: xxxxx@rkk.cz
> > To unsubscribe send a blank email to leave-ntdev-$subst(‘Recip.MemberIDChar’)@lists.osr.com
> >
>
>—
>You are currently subscribed to ntdev as: xxxxx@hotmail.com
>To unsubscribe send a blank email to leave-ntdev-$subst(‘Recip.MemberIDChar’)@lists.osr.com
Get your FREE download of MSN Explorer at http://explorer.msn.com
You are currently subscribed to ntdev as: $subst(‘Recip.EmailAddr’)
To unsubscribe send a blank email to leave-ntdev-$subst(‘Recip.MemberIDChar’)@lists.osr.com