Hi.
My target machone hasn’t any serial and 1394 ports. Is there any way to set
up a debugger in different way. Something like USB to COM mapper devices. Or
else?
Thanx in advance.
USB based COM ports don’t work. Do you have any expansion slots in this
device? You could plug in a serial or 1394 pcmcia or pci adapter to one of
these…
/simgr
-----Original Message-----
From: xxxxx@lists.osr.com
[mailto:xxxxx@lists.osr.com] On Behalf Of Dmitry Gubarkov
Sent: Wednesday, January 26, 2005 10:03 AM
To: Kernel Debugging Interest List
Subject: [windbg] no serial port problem
Hi.
My target machone hasn’t any serial and 1394 ports. Is there any way to set
up a debugger in different way. Something like USB to COM mapper devices. Or
else?
Thanx in advance.
You are currently subscribed to windbg as: xxxxx@stratus.com
To unsubscribe send a blank email to xxxxx@lists.osr.com
If your host is the USB side you can run that to a USB to serial converter
and then connect the resulting serial output from the converter to the
target. Unfortunately at this time a target without a serial port is a
problem. The target must have a hard serial port as USB to Serial will not
work.
–
The personal opinion of
Gary G. Little
“Dmitry Gubarkov” wrote in message news:xxxxx@windbg…
> Hi.
>
> My target machone hasn’t any serial and 1394 ports. Is there any way to
set
> up a debugger in different way. Something like USB to COM mapper devices.
Or
> else?
>
> Thanx in advance.
>
>
>
Use SoftICE then.
Calvin Guan Software Engineer
ATI Technologies Inc. www.ati.com
-----Original Message-----
From: Dmitry Gubarkov [mailto:xxxxx@ukr.net]
Sent: January 26, 2005 10:03 AM
To: Kernel Debugging Interest List
Subject: [windbg] no serial port problemHi.
My target machone hasn’t any serial and 1394 ports. Is there
any way to set
up a debugger in different way. Something like USB to COM
mapper devices. Or
else?Thanx in advance.
You are currently subscribed to windbg as: xxxxx@ati.com
To unsubscribe send a blank email to xxxxx@lists.osr.com
http://www.hawkingtech.com/prodSpec.php?ProdID=31
“Dmitry Gubarkov”
Sent by: xxxxx@lists.osr.com
01/26/2005 07:02 AM
Please respond to
“Kernel Debugging Interest List”
To
“Kernel Debugging Interest List”
cc
Subject
[windbg] no serial port problem
Hi.
My target machone hasn’t any serial and 1394 ports. Is there any way to
set
up a debugger in different way. Something like USB to COM mapper devices.
Or
else?
Thanx in advance.
—
You are currently subscribed to windbg as: karamata@us.ibm.com
To unsubscribe send a blank email to xxxxx@lists.osr.com
Thanx everybody for answers.
“Dmitry Gubarkov” wrote in message news:xxxxx@windbg…
> Hi.
>
> My target machone hasn’t any serial and 1394 ports. Is there any way to
> set up a debugger in different way. Something like USB to COM mapper
> devices. Or else?
>
> Thanx in advance.
>
>
Some legacy free machines like some models of the Compaq iPaq desktop had a serial header on the motherboard even though no port was exposed on the case.
You might check your motherboard for such a header.
Or better yet, why don’t you buy a cheap 1394 card and use that? You should be able to get one for about $20.
----- Original Message -----
From: Chris Karamatas
To: Kernel Debugging Interest List
Sent: Wednesday, January 26, 2005 12:30 PM
Subject: Re: [windbg] no serial port problem
http://www.hawkingtech.com/prodSpec.php?ProdID=31
“Dmitry Gubarkov”
Sent by: xxxxx@lists.osr.com
01/26/2005 07:02 AM Please respond to
“Kernel Debugging Interest List”
To “Kernel Debugging Interest List”
cc
Subject [windbg] no serial port problem
Hi.
My target machone hasn’t any serial and 1394 ports. Is there any way to set
up a debugger in different way. Something like USB to COM mapper devices. Or
else?
Thanx in advance.
—
You are currently subscribed to windbg as: karamata@us.ibm.com
To unsubscribe send a blank email to xxxxx@lists.osr.com
— You are currently subscribed to windbg as: xxxxx@msn.com To unsubscribe send a blank email to xxxxx@lists.osr.com